Finnish Sauna Expert Lassi Liikkanen on the Design Mistakes Americans Keep Making
By Arlene Scott
Correspondent, Research and Industry
- Published
- Reading time
- 7 min
SaunaNews is published by SaunaShare, Inc., which also runs SaunaShare.com and SaunaMarketplace.com, where we sell many of the products we write about. That experience may change what we write about and what we don't. Who owns SaunaNews · The ownership announcement
The Saunologia.fi founder, who has published over 400 articles and multiple books on sauna design, walked through the fundamentals in a recent webinar. Most problems trace back to three things.
In this story5 sections
Lassi Liikkanen has been writing about Finnish sauna design for over a decade. He runs Saunologia.fi, where he’s published more than 400 articles on the technical side of sauna construction. He’s written two books on the subject (Secrets of Finnish Sauna Design and the Finisana construction book, both available globally), and he provides architectural sauna design services through Finnish Sauna Design to clients from Utah to Tampere. In a recent webinar now available on YouTube, he walked through the fundamentals of what makes a Finnish sauna work and, more usefully, the specific design mistakes he keeps seeing in projects outside Finland.
What makes a Finnish sauna a Finnish sauna
Liikkanen’s definition is straightforward: a hot room with a visible heater containing rocks that allows people to create loyly (steam). Temperature ranges from 140°F to 220°F. That range is broader than many people expect. He made a point of noting that in the landmark Finnish health studies by Professor Jari Laukkanen, the average sauna temperature used by participants was only about 169°F. The popular idea that you need to push past 200°F to get health benefits doesn’t hold up in the research.
The loyly is the key differentiator. When water hits hot rocks, it creates steam that condenses on your skin, transferring heat energy far more effectively than dry air alone. What looks like sweat in a Finnish sauna may actually be condensation. This is the mechanism that separates a Finnish sauna from an infrared cabin (dry, moderate temperature, no steam) or a steam room (fully saturated, low temperature, tiled).
Getting into the sauna must be more fun than getting out of the sauna.
The three big design mistakes
Liikkanen identified three categories of problems that show up repeatedly in sauna projects, especially in North America:
1. The sauna is too big. Oversized saunas are expensive to heat, take forever to reach temperature, and feel uncomfortable when only one or two people are using them. Liikkanen recommends starting with design capacity (how many people?) and working backward. Each person needs roughly 2x2 feet of bench space. A comfortable minimum is about 6x5 or 6x6 feet of interior space.
2. The heater is the wrong size. You need approximately one kilowatt of power for every 35 cubic feet of sauna volume. Too powerful and the room heats up but the stones stay cold, so your loyly suffers. Too weak and you’re fighting the one-hour UL 875 timer limit on North American heaters before the room even reaches temperature. Both problems are common. Getting the heater-to-room ratio right is one of the most consequential decisions in the whole build.
3. Ventilation is wrong. Too little ventilation and the air quality deteriorates, especially in commercial saunas. Too much and you’re bleeding heat and losing your loyly to the exhaust. Ventilation is the number one source of heat loss in most saunas, so getting it right is a balancing act. For indoor installations, Liikkanen recommends full mechanical ventilation, especially for commercial setups.
The bench height problem
If there was one point Liikkanen hammered home, it was bench height. Hot air rises, and all the heat and steam from loyly concentrates near the ceiling. If your top bench isn’t high enough, you’re sitting below the good stuff. The guideline: keep 40 to 48 inches between the top bench and the ceiling. This is where many North American builds fall short. Low ceilings, low benches, or both mean the sauna never delivers the experience it should.
On materials
Liikkanen also flagged material choices. Spruce and pine can produce sap at high temperatures, which is fine on lower walls but becomes a problem on upper surfaces where it can get into your hair or stick to your back. And he noted that many modern saunas that look beautiful in photos are nearly impossible to keep clean, a practical consideration that often gets lost in the design process.
Saunologia recommends an Estonian air-mixing unit
Saunologia has rated Saunum’s Base air-mixing unit a “Recommended Sauna Product”; Saunum’s products are designed and manufactured in Estonia. A Finnish reviewer recommending Estonian-made equipment shows how seriously Estonia’s sauna manufacturers are now taken in Finland. Saunum’s patented air blending technology directly addresses the ventilation and heat distribution problems Liikkanen identifies as the most common design failures, which may explain the endorsement.
Enjoyment first
The joy of a Finnish sauna, Liikkanen argues, should be reason enough to use it regularly. The longevity benefits that Professor Laukkanen’s research has documented are a bonus.
The full webinar recording is available on YouTube. Liikkanen’s design services and books are at finnishsaunadesign.fi, and his extensive library of technical articles is at Saunologia.fi. Several specialty dealers carry heaters from brands including Narvi and Homecraft that are well-suited to properly designed Finnish sauna rooms.
